Material guide

Laser engraving aluminum: which laser can do it

Aluminum is one of the most requested materials and one of the most misunderstood. Before you prepare a file, find out whether your laser can mark your aluminum at all.

Reviewed by the Vextrify team, tested in our own laser workshops · Updated · How we test

Try Vextrify free
01

Which laser marks which aluminum

A fiber laser marks bare aluminum directly. A diode or CO2 laser does not mark bare aluminum reliably on its own: most of the beam is reflected and the metal carries the heat away. It needs either a metal marking spray or paste, which the laser fuses onto the surface, or anodized aluminum, where it only has to remove or bleach the dyed layer. Anodized parts give strong contrast with all three lasers.

  • Fiber: bare and anodized
  • Diode and CO2: anodized, or bare with marking spray
  • Black anodizing: highest contrast
02

Bare aluminum

On a fiber laser, bare aluminum marks light grey to white, and repeated passes engrave into the metal. Dark marks on bare aluminum are harder and depend strongly on the source and settings. With a diode or CO2 laser, marking spray turns into a dark, bonded layer where the beam hits it, and the rest washes off. Results vary between sprays and lasers, so test on scrap first.

  • Fiber: light marks, deep engraving with passes
  • Spray: dark bonded mark on diode and CO2
  • Clean and degrease the surface first
03

Anodized aluminum

Anodizing grows a thin oxide layer that carries the color. The laser removes or bleaches it and the lighter metal shows through. That makes logos and text crisp on black anodizing with almost any laser. Photos and coloured anodizing are harder; the anodized aluminum guide covers both.

Read the anodized aluminum guide
04

Preparing logos, text and photos

Logos and text need clean vector edges: Vextrify's Vectorize and Contour turn a logo image into paths, and fills can be angled or cross-hatched for an even surface. On a light mark on a dark surface, photos need inverted logic; Photo Studio has a material profile for anodized aluminum and previews the dither before you engrave. Keep the first part small and on scrap.

  • Logo → vector paths
  • Even fills with angle or cross-hatch
  • Light-on-dark photos: test normal and inverted
Try Photo Studio
05

Finding your settings

There is no universal speed and power for aluminum: the laser source, lens, surface finish, coating and spray all change the result. Engrave a material test grid on a scrap piece of the same stock, pick the best field and save it as a recipe.

Make a test grid

Lasers Vextrify drives

The desktop app for macOS, Windows and Linux connects to these controllers directly and runs the job live.

Diode lasers

  • GRBL — USB or network
  • xTool D1 · D1 Pro · S1
  • Sculpfun · Ortur · Atomstack · Twotrees

G-code firmware

  • Marlin
  • Smoothieware
  • Snapmaker 2.0 · Artisan

CO2 lasers

  • Ruida — USB or network
  • TopWisdom
  • Trocen / AWC
  • K40 with stock M2 Nano board

Fiber galvo lasers

  • SEA-LASER / BSL — e.g. Leapion LM-30S
  • JCZ / EZCAD2 (BJJCZ LMC)
  • EZCad3

Common questions

Can a diode laser engrave aluminum?

On anodized aluminum, usually yes. On bare aluminum, only with a metal marking spray or paste; on its own the diode beam is mostly reflected.

Can a CO2 laser engrave aluminum?

It marks anodized aluminum by removing the coloured layer, and bare aluminum only with a marking spray. It does not engrave into bare aluminum.

Which laser is best for aluminum?

A fiber laser, because it marks bare aluminum directly and can engrave into it. For anodized parts, diode and CO2 lasers also give good contrast.

What speed and power should I use for aluminum?

It depends on your laser, lens and surface. Run a test grid on scrap of the same stock and save the best field; numbers from another machine rarely match.